Crawl Space Dehumidifier Sizing: What to Measure

Start with floor area, layout, sealing condition, temperature observations and known moisture sources.

Illustration of temperature, humidity and water collection as separate parts of a capacity comparison.
Illustrated planning concept. No specific model or installation is depicted.
On this page

Gather the inputs before choosing a pint rating

Start with floor area, layout, sealing condition, temperature observations and known moisture sources. Give those facts to the person assessing the building. Ask them to state the required moisture removal and the temperature and relative humidity that apply to it.

A manufacturer's coverage claim is a starting point for its stated assumptions. It is not a guarantee for every space of that area. A divided layout, outside-air entry or a water problem can leave questions that a square-foot figure cannot answer.

Input / Keep this distinction
InputKeep this distinction
Floor areaArea describes the space; it does not by itself supply a moisture load
Required removalRecord who supplied the duty and its conditions
Rating pointCompare temperature and relative humidity on both sides
Operating rangePermission to operate is separate from removal at that temperature
Physical envelopeCheck installed accessories and service access separately

Compare the same conditions

The Compact70 documents 70 pints/day at 80°F and 60% relative humidity, and 43.7 pints/day at 65°F and 60%. Those values describe different points for the same unit. The ratings guide keeps the points intact.

Suppose an assessment specifies 40 pints/day at 65°F and 60% relative humidity. Comparing that stipulated duty with 43.7 establishes that the published point meets that number. It does not establish the actual duty of your house or full installed fit. The example is arithmetic, not a field measurement.

Keep capacity and installation checks separate

Use the constraint worksheet for documented exclusions and unanswered questions once you have measurements. Leave duty blank if it has not been supplied. The worksheet deliberately does not turn floor area into a capacity recommendation.

Then check the drainage route and low-clearance requirements. A cabinet can have enough documented removal at one point while still being unsuitable for the proposed physical or drainage configuration.

Understand the space

Choose the type of equipment

Sources and limitations

Pre-Retrofit Assessment of Crawlspaces and Basements Checked 2026-11-11

U.S. Department of Energy, Building America Solution Center / PNNL · Document date: not established · Primary source

Document revision: Publication date or revision not established unless stated.

Narrative: Interior Moisture; Exterior Moisture; electrical and combustion safety

Moisture in a basement or crawlspace could come from interior or exterior sources.

An RH reading alone cannot identify the moisture source. The apparently mismatched summary matrix is excluded from our assessment. The narrative’s 50% and 70% thresholds are not universal crawlspace setpoints or current local code.

View source reference ↗
Dehumidifiers Checked 2026-11-11

U.S. Environmental Protection Agency, ENERGY STAR · Document date: not established · Primary source

Document revision: Publication date or revision not established unless stated.

Buying Guidance: Capacity; Water Removal; Operating Temperature

Portable room dehumidifiers are typically used to dehumidify a single room or space

The portable sizing chart does not establish sizing for every crawlspace model. This page does not verify certification, 20% savings, a low-temperature cutoff or an oversizing recommendation for our eight models. October 1, 2025 is the specification effective date, not the page publication date.

View source reference ↗
Dehumidifier Testing and Capacity Checked 2026-11-11

U.S. Environmental Protection Agency, ENERGY STAR · Document date: not established · Primary source

Document revision: Publication date or revision not established unless stated.

Capacity and energy efficiency metric; testing change

Capacity is defined as the amount of water removed per day (24 hours) at test conditions

The old/new capacity conversion table is approximate. It does not establish a model-specific conversion or a 65°F capacity estimate.

View source reference ↗
Santa Fe Compact70 product documentation Checked 2026-11-11

Santa Fe · Document date: not established · Primary source

Product specifications

Unit Dimensions 12"W x 12"H x 21"D

Product specifications

65°F and 60% RH Water Removal 43.7 Pints/Day

Product specifications

70 Pints

Product specifications

8.75 Gallons @ 80°F and 60% RH

Product specifications

4044110

Documentary evidence for the named model and revision. Checked date records retrieval. Each excerpt identifies its section or page; drawing transcriptions are labelled separately.

View source reference ↗

Documentary comparison. Confirm the exact model, configuration and installation requirements before ordering.